Product Description:
DC motor is a rotating motor that can transform DC electrical energy into mechanical energy (DC motor) or mechanical strength into DC electric energy (DC generator). It is a motor that can convert DC and mechanical energy into one one more. When it operates as a motor, it is a immediate present motor, which converts electrical strength into mechanical energy when it runs as a generator, it is a direct existing generator, which converts mechanical strength into electrical energy.
| Merchandise Name | Frequency Converter Exterior Rotor Long term Magnet Synchronous DC Motor |
| Motor Variety | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition construction | The composition of DC motor need to consist of two components: stator and rotor. The static component of DC motor is called stator. The major function of stator is to make magnetic discipline, which is composed of foundation, principal magnetic pole, commutation pole, stop cap, bearing and brush device. Working component is named rotor, whose major perform is to make electromagnetic torque and inductive electromotive pressure. It is the hub of vitality conversion of DC motor. So it is also frequently named armature, which is composed of rotor, armature main, armature winding, commutator and supporter. |
| Model | Z Sort |
| Seat quantity | Z315-Z1000 |
| electrical power | sixty~2800kW |
| Voltage | 220~1000V |
| Torque range | one.5 ~180kNm |
| Security level | IP23, IP44 |
| Cooling manner | IC06,IC17,IC37,IC81W |
| Running velocity | Constant Pace /Lower Pace /Change Velocity /High Speed Other |
| Major classification | DC Motor is a equipment that converts mechanical energy into DC energy. It is primarily used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation electricity supply of alternator. Even though in spots in which DC energy is essential, AC electricity rectifier is also used to convert AC into DC power, but from some facets of performance, AC rectifier power provide can not fully replace DC generator. |
| Software | DC motors are broadly utilised in tape recorders, online video recorders, video clip discs, electric powered shavers, hair dryers, digital watches, toys and so on. |
| Servicing approach | Specialist motor servicing centre motor servicing approach: cleaning stator and rotor – changing carbon brush or other elements – vacuum F stress dipping paint – drying – Calibration balance. one. Use surroundings ought to be usually dry, motor surface must be kept clean, air consumption must not be hindered by dust, fibers and other obstacles. two. When the thermal safety of the motor proceeds to function, it need to be ascertained whether or not the fault comes from the motor or the overload or the placing value of the protective unit is way too lower. After removing the fault, it can be set into procedure. 3, make certain that the motor is properly lubricated in the course of operation. The basic motor runs for about 5000 several hours, that is to say, lubricating grease should be additional or replaced. When bearing overheating or lubricating deterioration is found in procedure, the hydraulic pressure must alter lubricating grease in time. When replacing grease, the aged grease ought to be taken out, and the oil groove of bearing and bearing cover must be washed with gasoline. Then ZL-three lithium grease ought to be stuffed with one/2 (two poles) and 2/3 (four poles, 6 poles and 8 poles) of the cavity in between the inner and outer rings of the bearing. 4. When the existence of the bearing is more than, the vibration and noise of the motor will enhance obviously. When the radial clearance of the bearing reaches the following benefit, the bearing need to be changed. five, when removing the motor, it is Ok to eliminate the rotor from the shaft extension or the non extension finish. If it is not required to unload the enthusiast, it is a lot more practical to just take out the rotor from the non-axle extension end. When pulling out the rotor from the stator, the stator winding or insulation must be prevented from becoming destroyed. 6. When changing the windings, the form, measurement, turns and gauges of the unique windings need to be recorded. When these knowledge are lost, they need to be acquired from the maker and the original developed windings ought to be modified at will, which often deteriorates 1 or several functionality of the motor or even can make it unattainable to use them. |
